Solar Panel Maintenance and Cleaning

how to clean solar panels

Learn how to clean solar panels by rinsing with a hose, brushing gently with a soft-bristle brush and soapy water, and rinsing again, from the ground where you can. Never use a pressure washer, and check your inverter output before and after.

This guide covers upkeep only: cleaning, reading output, spotting faults and keeping birds out. For the wider picture of home solar panels and battery storage, start with the hub guide. Smaller balcony systems follow the same cleaning principles, and how do plug in solar panels work explains what those systems involve.

What to prepare before you clean

  • Manufacturer instructions: cleaning guidance is usually listed in the owner’s or installation manual, often available on the manufacturer’s website, according to SolarReviews. Read it first, because it overrides general advice.
  • The right tools: a garden hose with a spray attachment, a soft-bristle brush or soft rag, and mild dish soap. Enphase recommends a soft, non-abrasive brush and soapy water.
  • Safe access: work from the ground or another safe access point. If your array is ground-mounted, EnergySage notes you can clean with a water hose, dish soap and a soft rag without climbing onto a roof.
  • A baseline reading: note what your inverter shows before you start, so you can judge whether the clean made a difference.

Cleaning routine, step by step

The routine below suits most fixed arrays. If your roof cannot be reached from the ground, leave the job to a trained professional rather than climbing up.

Step 1: Read the inverter first

Record the current generation figure and the status light before you touch a panel. A low reading on a clear day suggests soiling or a fault, and the two need different responses, as the fault-signs section below explains.

Step 2: Pick a cool, dull time

Cleaning is best done on a cloudy day or in the early morning or evening, according to Taskrabbit. This gives you a settled surface to work on rather than glass that is drying as you wash it.

Step 3: Rinse the panels thoroughly

Begin with a garden hose and spray attachment to rinse the panels, as Taskrabbit advises. This lifts loose dust, leaves and grit before anything touches the glass, so the brush does not drag particles across it.

Step 4: Brush gently with soapy water

Use the soft-bristle brush with a mild soapy solution and work across the surface without pressing hard. Scratching or damaging the glass in any way will reduce a panel’s energy production, EnergySage warns, and that loss can outweigh the dirt you were removing. Stubborn bird droppings usually need a little more patience with the soapy brush, not more force.

Step 5: Choose your water and tools with care

Tap water or abrasive materials can lead to hard water stains and residue buildup, according to EnergySage. If your tap water leaves marks, deionised water, which has had its dissolved minerals removed, is the usual alternative for the final rinse. Never use a pressure washer: it can create cracks, and SolarReviews adds that it can break the framing seal and let water inside the panel.

Step 6: Rinse off the soap and re-check

Rinse away all soap so it does not dry into a film, then compare the inverter reading with your baseline once the sun is out. For snow, EnergySage says not to use a standard broom, shovel or other non-specialised tool; use a purpose-made snow rake or wait for it to clear.

How often to clean in the UK

Twice a year is a sensible starting point. EnergySage says most systems benefit from cleaning twice a year, in spring and autumn, and LG CY Power gives the same minimum, with more frequent cleaning for dusty or pollen-heavy locations.

Adjust that to your surroundings. EnergySage suggests about every six months in a dry or dusty environment and says quarterly cleanings may be recommended where dust or bird activity is high. Rain helps but is not the most effective method for thorough cleaning, according to Enphase, so do not rely on it alone. These figures come from US and general installer guidance, not UK-specific studies, so treat them as a baseline and let your own inverter readings decide when an extra clean is due.

Does cleaning increase output?

Often yes, though the gain depends on how dirty the panels were. EnergySage says a quick cleaning can boost performance by up to 25%, and its installers report typical increases of 10-25% depending on dirtiness and time since the last service. Taskrabbit puts the loss from grime at up to seven percent, so published figures vary widely and a lightly soiled array will gain far less than a neglected one.

SolarReviews estimates that not cleaning lowers solar savings by $79 per year on average, which suggests the financial case is modest for a clean array and stronger where droppings or dust build up. For how output is rated in the first place, see our guide to solar panel efficiency.

Reading the inverter and spotting faults

The inverter is your early warning system. Enphase says monitoring can be a daily or weekly routine, and a quick look at the generation figure and status light tells you whether output is normal for the weather.

Separate dirt from faults using what the drop looks like:

  • Gradual decline that recovers after a clean: this points to soiling. Add an extra clean to your schedule.
  • Sudden, large drop or zero output: check the inverter status light. In a string inverter system, inverter failure can temporarily shut down all your panels, according to Enphase, so a total stop is an inverter question before it is a panel question.
  • Visible cracks, scratches or discolouration: damaged glass reduces production, and cleaning will not reverse it. Photograph the damage and contact your installer.
  • A hot spot: a cell running noticeably hotter than its neighbours is a fault, not a dirt problem. Do not keep washing; ask an MCS installer to inspect it.

Anything involving wiring, the inverter or damaged panels belongs with a qualified installer, not a DIY fix.

Stopping birds nesting under panels

Birds occasionally nest beneath unprotected solar panels, and squirrels and other rodents have been known to chew wires, according to Enphase. Nests trap debris and droppings and can put cables at risk.

A low-angle view of a full array, where every panel surface needs the same gentle rinse and soft brushing.

Bird guard mesh fitted along the edge of the array closes the gap beneath the panels and is the standard physical deterrent. Ask an MCS installer to fit it rather than attaching it yourself, because Enphase stresses following the manufacturer’s maintenance guidelines and avoiding unauthorised modifications. Where birds are a regular problem, expect to clean more often, as EnergySage’s quarterly suggestion for bird-heavy areas indicates.

Hexagonal wire mesh with the sun glowing through its openings.

Professional cleaning and cost

A professional is the right choice when the array cannot be reached safely from the ground. One US installer states its technicians are trained in fall protection, which is the kind of competence to ask any cleaner about before you book.

Cost data in the evidence is American. EnergySage says professional cleaning usually costs around $150-$350 per visit, and SolarReviews says companies typically charge $5 to $15 per panel. UK prices will differ, so request written quotes and confirm the cleaner uses soft tools and no pressure washer.

Quick checkpoint table

Checkpoint What good looks like If not
Before cleaning Inverter reading and status light noted Investigate a fault light before washing
Method Hose rinse, soft brush, soapy water, no pressure washer Stop if a tool could scratch the glass
After cleaning Clear glass, no soap film or hard water marks Rinse again, using deionised water if tap water marks the glass
Output afterwards Reading recovers on a bright day Look for cracks, a hot spot or inverter shutdown
Under the array Mesh intact, no nesting material Ask an MCS installer to fit or repair bird guard mesh

These checkpoints draw on cleaning guidance from EnergySage and monitoring and pest advice from Enphase.

Frequently asked questions

Is rain enough to keep panels clean?

No. Enphase says rain is not the most effective method for thorough cleaning, so schedule a proper clean as well.

Will cleaning affect my warranty?

Follow the manufacturer’s maintenance guidelines and avoid unauthorised modifications. Enphase notes most panels and microinverters carry 25-year performance warranties, while string or central inverter warranties usually last 10 to 15 years.

How often should an installer inspect the system?

Enphase recommends a professional inspection once every five to ten years, and says wiring and electrical inspections suit the end of the workmanship warranty, usually five to ten years.

Can I clean a roof array myself?

Only if you can do it from the ground or another safe access point. Otherwise book a trained professional instead of climbing onto the roof.